Function Tables

Rotate the smartphone by 90 degrees to show the entire table.

Function table 0, factory setting

Inputs / outputs

No.

Terminal

Function

Inputs

1

10

Automatic, Manual mode, Centre positioning

2

11

3

12

4

13

Web edge guiding Sensor 1, Web edge guiding Sensor 2,
Web centre-line guiding Sensor 1 and Sensor 2

5

14

6

15

Arrow key right, arrow key left

7

18

8

19

Line / contrast / feature guiding Sensor 3

9

20

Keyboard interlock

10

21

Controller interlock (only for automatic mode)

11

22

Setup lock

12

23

Not used

Outputs

1

26

Position of the guiding device corrected in operating mode automatic

2

27

Software limit switch active/Motor overcurrent/Guiding device in end position

3

28

Brake function (actuator EMS 23B)

4

29

Not used

 

Rotate the smartphone by 90 degrees to show the entire table.

Function table 1

Inputs / outputs

No.

Terminal

Function

Inputs

1

10

Automatic, Manual mode, Centre positioning

2

11

3

12

4

13

Web edge guiding Sensor 1, Web edge guiding Sensor 2,
Web centre-line guiding Sensor 1 and Sensor 2

5

14

6

15

Arrow key right, arrow key left

7

18

8

19

Line / contrast / feature guiding Sensor 3

9

20

Keyboard interlock

10

21

Controller interlock (only for automatic mode)

11

22

Selection of parameter sets 1 to 4 for the guiding setpoint (terminal assignment, see Selection of Parameter Set For The Guiding Setpoint)

12

23

Outputs

1

26

Position of the guiding device corrected in operating mode automatic

2

27

Software limit switch active/Motor overcurrent/Guiding device in end position

3

28

Brake function (actuator EMS 23B)

4

29

Not used

 

Rotate the smartphone by 90 degrees to show the entire table.

Function table 2

Inputs / outputs

No.

Terminal

Function

Inputs

1

10

Automatic, Manual mode, Centre positioning

2

11

3

12

4

13

Web edge guiding Sensor 1, Web edge guiding Sensor 2,
Web centre-line guiding Sensor 1 and Sensor 2

5

14

6

15

Arrow key right, arrow key left

7

18

8

19

Line / contrast / feature guiding Sensor 3

9

20

Keyboard interlock

10

21

Controller interlock (only for automatic mode)

11

22

External limit switch 1 (stroke limitation)

12

23

External limit switch 2 (stroke limitation)

Outputs

1

26

Position of the guiding device corrected in operating mode automatic

2

27

Software limit switch active/Motor overcurrent/Guiding device in end position

3

28

Brake function (actuator EMS 23B)

4

29

Not used

 

Rotate the smartphone by 90 degrees to show the entire table.

Function table 3

Inputs / outputs

No.

Terminal

Function

Inputs

1

10

Automatic, Manual mode, Centre positioning

2

11

3

12

4

13

Web edge guiding Sensor 1, Web edge guiding Sensor 2,
Web centre-line guiding Sensor 1 and Sensor 2

5

14

6

15

Arrow key right, arrow key left

7

18

8

19

Line / contrast / feature guiding Sensor 3

9

20

Keyboard interlock

10

21

Controller interlock (only for automatic mode)

11

22

Setup lock

12

23

1 = OK relay is used for status of the line monitoring

Outputs

1

26

Warning line position

2

27

Error line position

3

28

Warning line width

4

29

Error line width

 

Rotate the smartphone by 90 degrees to show the entire table.

Function table 4

Inputs / outputs

No.

Terminal

Function

Inputs

1

10

Automatic, Manual mode, Centre positioning

2

11

3

12

4

13

Web edge guiding Sensor 1, Web edge guiding Sensor 2,
Web centre-line guiding Sensor 1 and Sensor 2

5

14

6

15

Accept the current web position analogue Sensor 2 as guiding setpoint for analogue Sensor 1 or vice-versa

7

18

Inversion of the value accepted for the guiding setpoint
(0 = value not inverted, 1 = value inverted)

8

19

When accepting the guiding setpoint, the input signal of the EFE 1 is included. DIL switch S4.3 must be OFF.

9

20

Keyboard interlock

10

21

Controller interlock (only for automatic mode)

11

22

Selection of parameter sets 1 to 4 for the guiding setpoint (terminal assignment, see Selection of Parameter Set For The Guiding Setpoint)

12

23

Outputs

1

26

Position of the guiding device corrected in operating mode automatic

2

27

Software limit switch active/Motor overcurrent/Guiding device in end position

3

28

Brake function (actuator EMS 23B)

4

29

Not used

 

Rotate the smartphone by 90 degrees to show the entire table.

Function table 5

Inputs / outputs

No.

Terminal

Function

Inputs

1

10

Automatic, Manual mode, Centre positioning

2

11

3

12

4

13

Web edge guiding Sensor 1, Web edge guiding Sensor 2,
Web centre-line guiding Sensor 1 and Sensor 2

5

14

6

15

Arrow key right, arrow key left

7

18

8

19

Line / contrast / feature guiding Sensor 3

9

20

Keyboard interlock

10

21

Controller interlock (only for automatic mode)

11

22

Accept current position of a web edge as guiding setpoint

12

23

Not used

Outputs

1

26

Position of the guiding device corrected in operating mode automatic

2

27

Software limit switch active/Motor overcurrent/Guiding device in end position

3

28

Brake function (actuator EMS 23B)

4

29

Line/contrast sensor CLS Pro 600: Controller interlock,
Object sensor CLS CAM 100: Loss of the line / contrast / print feature

 

Rotate the smartphone by 90 degrees to show the entire table.

Function table 6

Inputs / outputs

No.

Terminal

Function

Inputs

1

10

Automatic, Manual mode, Centre positioning

2

11

3

12

4

13

Web edge guiding Sensor 1, Web edge guiding Sensor 2,
Web centre-line guiding Sensor 1 and Sensor 2

5

14

6

15

Arrow key right, arrow key left

7

18

8

19

Accept current position of a web edge as guiding setpoint

9

20

Keyboard interlock

10

21

Controller interlock (only for automatic mode)

11

22

Selection of parameter sets 1 to 4 for the guiding setpoint (terminal assignment, see Selection of Parameter Set For The Guiding Setpoint)

12

23

Outputs

1

26

Position of the guiding device corrected in operating mode automatic

2

27

Software limit switch active/Motor overcurrent/Guiding device in end position

3

28

Brake function (actuator EMS 23B)

4

29

Line/contrast sensor CLS Pro 600:
Controller interlock (digital output DOUT)

 

Rotate the smartphone by 90 degrees to show the entire table.

Function table 7

Inputs / outputs

No.

Terminal

Function

Inputs

1

10

Automatic, Manual mode, Centre positioning

2

11

3

12

4

13

Web edge guiding Sensor 1, Web edge guiding Sensor 2,
Web centre-line guiding Sensor 1 and Sensor 2

5

14

6

15

Arrow key right, arrow key left

7

18

8

19

Line / contrast / feature guiding Sensor 3

9

20

Keyboard interlock

10

21

Controller interlock (only for automatic mode)

11

22

Setup lock

12

23

Not used

Outputs

1

26

Position of the guiding device corrected in operating mode automatic

2

27

Automatic

3

28

Manual mode

4

29

Centre positioning

 

Rotate the smartphone by 90 degrees to show the entire table.

Function table 8

Inputs / outputs

No.

Terminal

Function

Inputs

1

10

Automatic, Manual mode, Centre positioning

2

11

3

12

4

13

Web edge guiding Sensor 1, Web edge guiding Sensor 2,
Web centre-line guiding Sensor 1 and Sensor 2

5

14

6

15

Arrow key right, arrow key left

7

18

8

19

Line / contrast / feature guiding Sensor 3

9

20

Keyboard interlock

10

21

Controller interlock (only for automatic mode)

11

22

Setup lock

12

23

Oscillation on/off

Outputs

1

26

Position of the guiding device corrected in operating mode automatic

2

27

Software limit switch active/Motor overcurrent/Guiding device in end position

3

28

Brake function (actuator EMS 23B)

4

29

Controller interlock (only for automatic mode)

 

Rotate the smartphone by 90 degrees to show the entire table.

Function table 9

Inputs / outputs

No.

Terminal

Function

Inputs

1

10

Automatic, Manual mode, Centre positioning

2

11

3

12

4

13

Web edge guiding Sensor 1, Web edge guiding Sensor 2,
Web centre-line guiding Sensor 1 and Sensor 2

5

14

6

15

Arrow key right, arrow key left

7

18

8

19

Line / contrast / feature guiding Sensor 3

9

20

Keyboard interlock

10

21

Controller interlock (only for automatic mode)

11

22

Setup lock

12

23

Not used

Outputs

1

26

Position of the guiding device corrected in operating mode automatic

2

27

Width measurement warning

3

28

Width measurement error

4

29

Not used

 

Rotate the smartphone by 90 degrees to show the entire table.

Function table 10

Inputs / outputs

No.

Terminal

Function

Inputs

1

10

Automatic, Manual mode, Centre positioning

2

11

3

12

4

13

Web edge guiding Sensor 1, Web edge guiding Sensor 2,
Web centre-line guiding Sensor 1 and Sensor 2

5

14

6

15

Arrow key right, arrow key left

7

18

8

19

Moving the sensor slide of positioning unit 1 to the left

9

20

Moving the sensor slide of positioning unit 1 to the right

10

21

Moving the sensor slide of positioning unit 2 to the left

11

22

Moving the sensor slide of positioning unit 2 to the right

12

23

Not used

Outputs

1

26

Position of the guiding device corrected in operating mode automatic

2

27

Software limit switch active/Motor overcurrent/Guiding device in end position

3

28

Brake function (actuator EMS 23B)

4

29

Not used

 

Rotate the smartphone by 90 degrees to show the entire table.

Function table 11

Inputs / outputs

No.

Terminal

Function

Inputs

1

10

Automatic, Manual mode, Centre positioning

2

11

3

12

4

13

Web edge guiding Sensor 1, Web edge guiding Sensor 2,
Web centre-line guiding Sensor 1 and Sensor 2

5

14

6

15

Arrow key right, arrow key left

7

18

8

19

Line / contrast / feature guiding Sensor 3

9

20

Keyboard interlock

10

21

Controller interlock (only for automatic mode)

11

22

Setup lock

12

23

Not used

Outputs

1

26

Position of the guiding device corrected in operating mode automatic

2

27

Software limit switch active/Motor overcurrent/Guiding device in end position

3

28

Material in Sensor 1*

4

29

Material in Sensor 2*

* Indicates that there is material within the sensor scanning area (even with full coverage of the sensor scanning area)

 

Rotate the smartphone by 90 degrees to show the entire table.

Function table 12

Inputs / outputs

No.

Terminal

Function

Inputs

1

10

Automatic, Manual mode, Centre positioning

2

11

3

12

4

13

Web edge guiding Sensor 1, Web edge guiding Sensor 2,
Web centre-line guiding Sensor 1 and Sensor 2

5

14

6

15

Arrow key right, arrow key left

7

18

8

19

Line / contrast / feature guiding Sensor 3

9

20

Keyboard interlock

10

21

Controller interlock (only for automatic mode)

11

22

Setup lock

12

23

Not used

Outputs

1

26

Position of the guiding device corrected in operating mode automatic

2

27

The selected sensor has detected a web edge.**

3

28

Sensor 1 has detected a web edge.**

4

29

Sensor 2 has detected a web edge.**

** With full coverage of the sensor scanning area no web edge will be detected.

Rotate the smartphone by 90 degrees to show the entire table.

Function table 13

Inputs / outputs

No.

Terminal

Function

Inputs

1

10

Automatic, Manual mode, Centre positioning

2

11

3

12

4

13

Keyboard interlock

5

14

Web edge guiding Sensor 2

6

15

Arrow key right, arrow key left

7

18

8

19

Line / contrast / feature guiding Sensor 3

9

20

Web edge guiding Sensor 1

10

21

Controller interlock (only for automatic mode)

11

22

Setup lock

12

23

Not used

Outputs

1

26

Position of the guiding device corrected in operating mode automatic

2

27

Software limit switch active/Motor overcurrent/Guiding device in end position

3

28

Brake function (actuator EMS 23B)

4

29

Not used

 

Function table 14

Reserved for special applications

 

Rotate the smartphone by 90 degrees to show the entire table.

Function table 15

Inputs / outputs

No.

Terminal

Function

Inputs

1

10

Automatic, Manual mode, Centre positioning

2

11

3

12

4

13

Web edge guiding Sensor 1, Web edge guiding Sensor 2,
Web centre-line guiding Sensor 1 and Sensor 2

5

14

6

15

Arrow key right, arrow key left

7

18

8

19

Line / contrast / feature guiding Sensor 3

9

20

Combi sensor: Sensor A active

10

21

Combi sensor: Sensor B active

11

22

Combi sensor on sensor positioner: Sensor A active

12

23

Combi sensor on sensor positioner: Sensor B active

Outputs

1

26

Position of the guiding device corrected in operating mode automatic

2

27

Software limit switch active/Motor overcurrent/Guiding device in end position

3

28

Brake function (actuator EMS 23B)

4

29

Not used

 

Rotate the smartphone by 90 degrees to show the entire table.

Function table 16

 

Inputs / outputs

No.

Terminal

Function

Inputs

1

10

Automatic, Manual mode, Centre positioning

2

11

3

12

4

13

Web edge guiding Sensor 1, Web edge guiding Sensor 2,
Web centre-line guiding Sensor 1 and Sensor 2

5

14

6

15

Arrow key right, arrow key left

7

18

8

19

Line / contrast / feature guiding Sensor 3

9

20

Controller interlock web edge guiding Sensor 1

10

21

Controller interlock web edge guiding Sensor 2

11

22

Keyboard interlock

12

23

Not used

Outputs

1

26

Position of the guiding device corrected in operating mode automatic

2

27

Software limit switch active/Motor overcurrent/Guiding device in end position

3

28

Brake function (actuator EMS 23B)

4

29

Controller interlock (blocking)

 

Rotate the smartphone by 90 degrees to show the entire table.

Function table 17

 

Inputs / outputs

No.

Terminal

Function

Inputs

1

10

Automatic, Manual mode, Centre positioning

2

11

3

12

4

13

Web edge guiding Sensor 1, Web edge guiding Sensor 2,
Web centre-line guiding Sensor 1 and Sensor 2

5

14

6

15

Arrow key right, arrow key left

7

18

8

19

Line / contrast / feature guiding Sensor 3

9

20

Keyboard interlock

10

21

Controller interlock (only for automatic mode)

11

22

External limit switch 1 (stroke limitation),
input inverted (wire-break proof)

12

23

External limit switch 2 (stroke limitation),
input inverted (wire-break proof)

Outputs

1

26

Position of the guiding device corrected in operating mode automatic

2

27

Software limit switch active/Motor overcurrent/Guiding device in end position

3

28

Brake function (actuator EMS 23B)

4

29

Not used

 

Rotate the smartphone by 90 degrees to show the entire table.

Function table 18

 

Inputs / outputs

No.

Terminal

Function

Inputs

1

10

Automatic, Manual mode, Centre positioning

2

11

3

12

4

13

Web edge guiding Sensor 1, Web edge guiding Sensor 2,
Web centre-line guiding Sensor 1 and Sensor 2

5

14

6

15

Arrow key right, arrow key left

7

18

8

19

Line / contrast / feature guiding Sensor 3

9

20

Keyboard interlock

10

21

Controller interlock (only for automatic mode)

11

22

Take over the current ACTUAL position as the SETPOINT position for the selected guiding mode

Requirement:
The acceptance mode “Automatic acceptance with remote control signal” is activated (parameter list 0, w-setup by input = 1 (ON)).

12

23

Reset the SETPOINT position for the selected guiding mode to "0“

Outputs

1

26

Position of the guiding device corrected in operating mode automatic

2

27

Software limit switch active/Motor overcurrent/Guiding device in end position

3

28

Brake function (actuator EMS 23B)

4

29

Line/contrast sensor CLS Pro 600: Controller interlock,
Object sensor CLS CAM 100: Loss of the line / contrast / print feature

 

Rotate the smartphone by 90 degrees to show the entire table.

Function table 19

 

Inputs / outputs

No.

Terminal

Function

Inputs

1

10

Automatic, Manual mode, Centre positioning

2

11

3

12

4

13

Web edge guiding Sensor 1, Web edge guiding Sensor 2,
Web centre-line guiding Sensor 1 and Sensor 2

5

14

6

15

Arrow key right, arrow key left

7

18

8

19

Line / contrast / feature guiding Sensor 3

9

20

Keyboard interlock

10

21

Controller interlock (only for automatic mode)

11

22

Setup lock

12

23

Not used

Outputs

1

26

Position of the guiding device corrected in operating mode automatic

2

27

Software limit switch active/Motor overcurrent/Guiding device in end position

3

28

Brake function (actuator EMS 23B)

4

29

Dead zone operation:
The web edge is located within a range with reduced controller gain or with controller gain = 0.